Dec 11, 2023 Leave a message

S355NL Steel Plate: Normalized Fine Grain Properties

What S355NL Steel Plate Is

S355NL is a weldable fine grain structural steel plate specified in EN 10025-3, the part of the European structural steel standard that covers normalized and normalized rolled grades. Reading the designation from left to right gives the whole specification: S stands for structural steel, 355 is the minimum yield strength in megapascals for the thinnest thickness range, N states that the plate is delivered in the normalized or normalized rolled condition, and L states that the steel is verified for impact energy at a test temperature of minus 50 degrees Celsius. The complete standard designation is written as EN 10025-3 S355NL, often followed by the delivery condition symbol +N.

The distinction between S355NL and the more common S355J2 or S355JR grades of EN 10025-2 is not a matter of strength; all three share the same 355 MPa minimum yield level at thin sections. The difference lies in two requirements that EN 10025-2 does not impose: a fine austenitic grain size obtained by aluminium killing with or without niobium and vanadium microalloying, and a guaranteed Charpy impact energy at a sub-zero temperature far below the minus 20 degrees Celsius used for the J2 grade. Those two requirements make S355NL the appropriate choice for structures that operate in cold climates, for equipment that must be qualified for low-temperature service, and for thick welded joints where a coarse heat-affected zone would otherwise be the weak link.

Chemical Composition Requirements

EN 10025-3 controls both the individual element maxima and the carbon equivalent value. The ladle analysis limits for S355N and S355NL at the usual plate thicknesses are shown below; the product analysis tolerances permitted by the standard apply on top of these figures, and a certificate that reports values above the limit is a non-conformance regardless of the mechanical results.

Element Requirement, % Notes on control
Carbon 0.18 max Upper limit applies to all thicknesses; lower carbon improves heat-affected zone toughness
Silicon 0.50 max Deoxidation residual
Manganese 0.90 - 1.65 Range, not a maximum; a low manganese heat may fail strength
Phosphorus 0.025 max Restricted against temper and plate cracking
Sulphur 0.020 max Restricted further when Z quality is ordered
Niobium 0.05 max Grain refinement; counts toward carbon equivalent
Vanadium 0.12 max Precipitation strengthening
Titanium 0.05 max Nitride former, protects grain size near the weld
Aluminium, total 0.020 min Required as the fine grain killing element
Nitrogen 0.015 max Free nitrogen reduces toughness
Copper, chromium, nickel, molybdenum 0.55 / 0.30 / 0.50 / 0.10 max Residual elements, each capped
Carbon equivalent, CEV 0.43 max Weldability index; the controlling number for procedures

The carbon equivalent value deserves more attention than any single element. It is calculated from the carbon, manganese, chromium, molybdenum, vanadium, nickel and copper contents, and it correlates with the hardness that will form in the heat-affected zone during welding. A steel that meets every single-element limit but lands at a carbon equivalent of 0.46 will weld harder and crack more readily than a 0.41 steel, and the preheat calculation must follow the actual certified value rather than the grade limit.

Mechanical Properties by Thickness

Yield strength falls with increasing plate thickness because the amount of deformation in the centre of a thick plate is lower and the cooling rate after normalizing is slower. EN 10025-3 handles this by publishing a stepped table, and the buyer must check the property at the ordered thickness, not at the headline 355 MPa value that applies only to thin plate.

Thickness range, mm Minimum yield strength, MPa Tensile strength, MPa Minimum elongation, %
16 and under 355 470 - 630 22
Over 16 to 40 345 470 - 630 22
Over 40 to 63 335 470 - 630 21
Over 63 to 80 325 470 - 630 20
Over 80 to 100 315 470 - 630 20
Over 100 to 150 295 450 - 600 19
Over 150 to 200 285 450 - 600 18
Over 200 to 250 275 450 - 600 18

Impact testing is the defining feature of the NL suffix. The standard requires Charpy V-notch testing at minus 50 degrees Celsius with a minimum average absorbed energy, evaluated on a set of three specimens with a permitted minimum for any single specimen. The N grade, by contrast, is tested at plus 20 degrees Celsius, and a plate certified only as S355N must never be accepted for a minus 50 degree design condition even though the tensile values are identical. The test piece orientation, usually transverse to the rolling direction, and the specimen location, normally at a specified distance from the rolled surface, must match the requirement of the design code.

Normalizing and Fine Grain Practice

The N designation means the plate has been normalized, that is, heated to a temperature above the upper transformation point and cooled in still air, or has been normalized rolled, a route in which the final rolling passes are performed in a temperature range that reproduces the effect of normalizing without a separate furnace cycle. Both routes deliver a uniform ferrite-pearlite microstructure with an austenitic grain size of 6 or finer when assessed by the relevant grain size method, and both are acceptable under EN 10025-3 with the +N symbol on the certificate.

Normalizing brings two practical benefits. It removes the banding and property variation that as-rolled plate can show through the thickness, and it makes the plate tolerant of a subsequent hot forming operation, because the forming heat cycle can be followed by a repeat normalize and the properties will be restored. That tolerance is the main reason normalizing is chosen for formed heads, dished ends and rolled shells in low-temperature equipment. The cost is a slower production route with higher energy consumption, which shows up in the price relative to as-rolled or TMCP alternatives.

What normalizing does not tolerate is careless thermal treatment after delivery. Every normalize or stress relief cycle must stay within the qualified range, and repeated excursions above the normalizing temperature cause grain coarsening that no subsequent operation will correct.

Through-Thickness (Z) Quality

Thick plates welded into T-joints and corner joints are loaded in the through-thickness direction by weld shrinkage, and a plate with a central segregation band containing elongated manganese sulphide inclusions will tear internally at strains well below the plate's in-plane ductility. EN 10164 provides the remedy through a Z designation based on the reduction of area measured on a tensile specimen taken in the thickness direction.

Z designation Minimum reduction of area, % Where it is normally specified
Z15 15 Moderate restraint, plate 30 to 60 mm
Z25 25 Heavy welded box sections and node joints
Z35 35 Highly restrained thick joints, offshore and crane structures

Ordering Z quality implies more than an added test. The mill must use calcium treatment or another inclusion shape control practice and must hold sulphur well below the standard maximum, because elongated type II sulphides are the principal cause of low through-thickness ductility. A Z designation ordered without those process controls produces a plate that fails the test rather than a plate that passes it.

Welding S355NL Plate

S355NL is welded with the conventional arc processes. Because the carbon content is capped at 0.18% and the carbon equivalent at 0.43, the steel is generally more forgiving than a higher-carbon structural plate of the same strength, but low-temperature toughness is lost in the heat-affected zone if heat input and preheat are uncontrolled. The coarse-grained region adjacent to the fusion line is the critical location: it is where the original fine grain structure is destroyed at temperatures above roughly 1100 degrees Celsius, and where Charpy values fall fastest.

A qualified procedure should control four variables. Preheat, calculated from the certified carbon equivalent and the combined thickness of the joint, typically falls in the range of 100 to 150 degrees Celsius for thick plate at the upper end of the carbon equivalent limit. Interpass temperature must be capped, usually at 250 degrees Celsius, because excessive interpass temperature coarsens the heat-affected microstructure and can reduce toughness below the acceptance level. Heat input should sit within the range used during procedure qualification, commonly 1.0 to 2.5 kilojoules per millimetre for the low-temperature grades, with the exact band confirmed by impact testing. Consumable hydrogen must be low, and basic flux or low-hydrogen electrodes are normal practice for thick joints.

After welding, verify the joint by visual inspection, ultrasonic or radiographic testing as required by the design code, and by hardness traverse where the specification calls for it. Post-weld heat treatment is not required for S355NL on account of the steel itself; it is applied when the section thickness or the service condition demands it, and the holding temperature should stay below the range at which the microalloying precipitates coarsen excessively.

Applications and Grade Selection

S355NL is specified where a structure must combine weldability, moderate strength and dependable toughness at low temperature. Typical uses include wind turbine towers and foundations, where the steel must remain ductile at winter service temperatures; hydropower penstocks, spiral cases and embedded parts; crane booms, port handling equipment and mining machinery frames; bridge components in cold climates; and general heavy fabrication of flanges, rings and machined structural parts cut from thick plate.

Selection against neighbouring grades follows a simple logic. Use S355J2 of EN 10025-2 where the lowest service temperature stays above minus 20 degrees Celsius and the plate is thin. Move to S355NL when the design temperature reaches minus 50 degrees Celsius, when the plate is thick enough for heat-affected zone toughness to govern, or when the design code explicitly demands fine grain practice. Move to S420NL or S460NL of the same standard when the strength requirement exceeds what 355 MPa can deliver at the ordered thickness. Above those levels, and where the application permits only moderate weldability, quenched and tempered grades become the alternative and require a different welding procedure entirely.

Ordering, Inspection and Storage

A complete order for S355NL plate states the standard and grade, the +N delivery condition, the dimensions with the tolerance standard, the impact test temperature and energy, the carbon equivalent limit, the Z designation if applicable, the ultrasonic inspection class for the intended joint, and the surface quality requirement. EN 10029 covers thickness, width and length tolerances for hot rolled plate, and EN 10160 covers ultrasonic testing of plate for internal discontinuities.

On delivery, check that the marking carries the heat number and plate number, that the certificate reports the actual impact energy at minus 50 degrees Celsius rather than a room-temperature value, and that the chemical analysis includes aluminium and nitrogen, since a certificate without those two elements cannot demonstrate fine grain practice. Store the plate clear of the ground on supports, avoid edge damage from lifting gear, and keep weathering or painted stock separated. Plate that has been stored for a long period should be inspected for edge corrosion before cutting, because corroded edges are a frequent source of weld defects in thick joints.

FAQ

Q: What is the difference between S355NL and S355J2?
Both are 355 MPa minimum yield structural steels. S355J2 belongs to EN 10025-2 and is impact tested at minus 20 degrees Celsius, while S355NL belongs to EN 10025-3 and is impact tested at minus 50 degrees Celsius with a mandatory fine grain, aluminium killed composition and a carbon equivalent limit.

Q: Is normalized rolling equivalent to normalizing?
For property purposes EN 10025-3 accepts normalized rolling in place of a separate normalize heat cycle, and both carry the +N symbol. The difference appears when the fabricator hot forms the plate, because a normalized rolled plate must generally be re-normalized after forming to restore the specified condition.

Q: What does S355NL mean in the grade name?
S denotes structural steel, 355 the minimum yield strength in megapascals at thin sections, N the normalized or normalized rolled delivery condition, and L a specified impact test temperature of minus 50 degrees Celsius.

Q: Can S355NL be used at temperatures below minus 50 degrees Celsius?
The grade guarantees impact energy at minus 50 degrees Celsius, so service below that temperature requires either a lower-temperature grade from the same standard, such as a steel qualified for minus 60 degrees Celsius in a dedicated low-temperature specification, or an engineering assessment supported by additional testing of the actual plate and weld joints.

Q: Why is the yield strength lower on a 100 mm plate than on a 20 mm plate?
Because thick plate receives less effective deformation at its centre and cools more slowly after normalizing, producing a slightly coarser ferrite grain size. EN 10025-3 accounts for this with a stepped property table, and the design must use the value that corresponds to the ordered thickness.

Q: When must Z quality be ordered with S355NL?
Z quality is needed where weld shrinkage strains the plate in the through-thickness direction, typically in T-joints and corner joints in plate thicker than about 30 mm, or wherever the design code imposes a through-thickness ductility requirement. It should be ordered together with a low sulphur limit and inclusion shape control.

Send Inquiry

whatsapp

phone

Email

Inquiry