Quenching and tempering are crucial heat treatment processes for low alloy steel plates, significantly enhancing their mechanical properties. As a low alloy steel plate supplier, I understand the importance of these processes in delivering high - quality products to our customers. In this blog, I'll delve into the quenching and tempering processes for low alloy steel plates, explaining their principles, procedures, and impacts on the steel's performance.
Quenching Process
Principle
Quenching is a rapid cooling process that involves heating the low alloy steel plate to a specific austenitizing temperature and then quickly cooling it in a quenching medium. The main purpose of quenching is to transform the austenite structure in the steel into martensite, a hard and brittle phase. This transformation occurs because the rapid cooling rate suppresses the diffusion - controlled phase transformations, such as the formation of ferrite and pearlite.
The austenitizing temperature for low alloy steel plates typically ranges from 800°C to 950°C, depending on the specific alloy composition. For example, some low alloy steels with a higher carbon content may require a slightly higher austenitizing temperature to ensure complete austenitization.
Quenching Medium
The choice of quenching medium is critical as it determines the cooling rate. Common quenching media include water, oil, and polymer solutions.
- Water: Water is an efficient quenching medium that provides a high cooling rate. It is relatively inexpensive and readily available. However, the high cooling rate can cause significant thermal stress in the steel plate, leading to distortion and cracking, especially for thicker plates or steels with high hardenability.
- Oil: Oil quenching provides a slower cooling rate compared to water. It is suitable for low alloy steel plates that require a more moderate cooling rate to avoid excessive stress. Oil quenching can reduce the risk of cracking, but it may not achieve the same high hardness as water quenching in some cases.
- Polymer Solutions: Polymer solutions offer a controllable cooling rate between water and oil. By adjusting the concentration of the polymer in the solution, the cooling rate can be tailored to the specific requirements of the low alloy steel plate. This makes polymer solutions a popular choice for many applications.
Procedure
The quenching process typically involves the following steps:
- Heating: The low alloy steel plate is heated in a furnace to the austenitizing temperature and held at this temperature for a sufficient time to ensure uniform austenitization. This holding time depends on the thickness of the plate and the heating rate of the furnace.
- Transfer: Once the steel plate reaches the austenitizing temperature, it is quickly transferred from the furnace to the quenching medium. Minimizing the transfer time is crucial to prevent the formation of unwanted phases during the cooling process.
- Quenching: The steel plate is immersed in the quenching medium and held there until it reaches a temperature below the martensite start temperature. During this process, the austenite transforms into martensite, resulting in a significant increase in hardness.
Tempering Process
Principle
After quenching, the low alloy steel plate is extremely hard and brittle due to the presence of martensite. Tempering is a subsequent heat treatment process that involves heating the quenched steel plate to a temperature below the lower critical temperature (usually between 150°C and 650°C) and then cooling it slowly. The main purpose of tempering is to relieve the internal stress generated during quenching, improve the toughness of the steel, and reduce its brittleness while maintaining a reasonable level of hardness.
Effects of Tempering Temperature
- Low - Temperature Tempering (150°C - 250°C): At low tempering temperatures, the main effect is to relieve the internal stress in the martensite. The hardness of the steel plate remains relatively high, and there is only a slight decrease in hardness. This type of tempering is often used for applications where high hardness and wear resistance are required, such as in cutting tools.
- Medium - Temperature Tempering (350°C - 500°C): Medium - temperature tempering results in a significant reduction in internal stress and an increase in toughness. The hardness of the steel plate decreases more compared to low - temperature tempering, but it still maintains a good balance between strength and toughness. This tempering range is suitable for springs and other components that require high elasticity.
- High - Temperature Tempering (500°C - 650°C): High - temperature tempering produces a microstructure of tempered sorbite, which has excellent combination of strength, toughness, and ductility. The hardness of the steel plate is further reduced, but the toughness is greatly improved. This type of tempering is commonly used for structural components, such as Alloy Steel Plate Q345A, that need to withstand high loads and impact forces.
Procedure
The tempering process includes the following steps:
- Heating: The quenched low alloy steel plate is heated in a furnace to the selected tempering temperature at a controlled heating rate. A slow heating rate is often preferred to prevent the development of additional thermal stress.
- Holding Time: The steel plate is held at the tempering temperature for a certain period to allow the necessary microstructural changes to occur. The holding time depends on the thickness of the plate and the tempering temperature.
- Cooling: After the holding time, the steel plate is cooled slowly in the furnace or in air, depending on the specific requirements. Slow cooling helps to further relieve the internal stress and ensure a stable microstructure.
Impact on Low Alloy Steel Plate Performance
Mechanical Properties
Quenching and tempering have a profound impact on the mechanical properties of low alloy steel plates.
- Hardness: Quenching increases the hardness of the steel plate by forming martensite. Tempering can adjust the hardness according to the tempering temperature. For example, S690Q S690QL High Strength Low Alloy Steel can achieve high hardness through proper quenching and then be tempered to obtain the desired combination of hardness and toughness.
- Strength: The strength of the low alloy steel plate is significantly improved after quenching and tempering. The martensite formed during quenching provides high strength, and tempering helps to optimize the strength - toughness balance. High - strength low alloy steel plates, such as A656 HSLA Steel Plate, often rely on quenching and tempering to achieve their superior strength characteristics.
- Toughness: Tempering is crucial for improving the toughness of the steel plate. By relieving internal stress and modifying the microstructure, tempering reduces the brittleness of the quenched steel and enhances its ability to absorb energy without fracturing.
Microstructure
The quenching and tempering processes also change the microstructure of the low alloy steel plate. Quenching transforms the austenite into martensite, which has a needle - like structure. Tempering then modifies this martensite structure. At low tempering temperatures, carbides start to precipitate within the martensite, and as the tempering temperature increases, the martensite gradually decomposes, and more stable microstructures such as tempered sorbite or tempered bainite are formed.


Quality Control in Quenching and Tempering
Nondestructive Testing
To ensure the quality of the quenched and tempered low alloy steel plates, nondestructive testing methods are often used. Ultrasonic testing can detect internal flaws such as cracks or porosity in the steel plate. Magnetic particle testing is suitable for detecting surface and near - surface defects in ferromagnetic low alloy steels.
Mechanical Testing
Mechanical testing is also essential. Tensile testing is used to measure the yield strength, ultimate tensile strength, and elongation of the steel plate. Hardness testing, such as Rockwell or Brinell hardness testing, can verify the hardness level achieved after quenching and tempering. Impact testing, such as Charpy V - notch testing, can evaluate the toughness of the steel plate.
Conclusion
As a low alloy steel plate supplier, we recognize the significance of quenching and tempering processes in producing high - quality steel plates. These heat treatment processes can transform the mechanical properties and microstructure of low alloy steel plates, making them suitable for a wide range of applications, from construction to machinery manufacturing.
If you are in need of high - quality quenched and tempered low alloy steel plates, we are here to provide you with the best products and services. Our team of experts can assist you in selecting the most appropriate steel grade and heat treatment process according to your specific requirements. Contact us for more information and to start a procurement negotiation. We look forward to serving you.
References
- ASM Handbook Volume 4: Heat Treating. ASM International.
- Metals Handbook: Properties and Selection: Irons, Steels, and High - Performance Alloys. ASM International.
- Heat Treatment Principles and Techniques. Elsevier.






